Cheap 800 RMS 4-ohm amp?

Let’s learn cheap 800 RMS 4-ohm amp. The most accurate or helpful solution is served by ebay.com.

There are ten answers to this question.

Best solution

4 Ohm Bridged RMS Power: ... Kicker KX800.1 1600 Watt Peak / 800 Watt RMS Class D Compact Car Audio Amplifier With Remote Bass Knob + Rockville ... About 800 RMS Amp.

ebay.com

Other solutions

I have TWO 12 " kicker CVR subs, 400 watts RMS 800 peak each at 4ohm. do i need a 800 RMS amp or 400 RMS @4ohm

Answer:

i've got the same speakers and ive got a 850 watt mono block amp and it does really good so i would...

tim m at Yahoo! Answers Mark as irrelevant Marked as irrelevant Undo

I have solobaric 2 15s from kicker and there between 800 and 900 watt rms...my question is will a tis amp of 1800 watts(1200 watt rms i believe) push these real good..these are the specs for the amp...1x1800watt peak power@4ohm bridged...2x600watt rms@2oh

Answer:

It depends how you are going to wire the subs? Are you running them in a series? or parallel? what is...

MaKaveLi at Answerbag.com Mark as irrelevant Marked as irrelevant Undo

I Have 2 Kicker CVR 12" Dual 4ohm Subs. RMS: 800 Watts Per Pair / 400 Watts Each. Is A Hitron HPA2000.1D Class D Amp 2000w Max RMS Power Rating: 4 Ohms: 750 Watts X 1 Chan. 2 Ohms: 1200 Watts X 1 Chan. A Big (good Enough) Amp For The Subs?

Answer:

Seeing on the specs it seems like a good amp. But it all depends on how you are wiring the subs. If...

Martin Jolles at Blurtit.com Mark as irrelevant Marked as irrelevant Undo

What should the rms and max be on subs for a 1100 watt amp....?

i have a crunch p1100.2 its a 2 channel amp its ratings are 2x250w at 4ohms each channel 2x550 at 2 ohms each channel and 1x1100 at 4ohms im thinking 2 channel set up at 2 ohms but my last sub was 1200 watts max and 400 rms 4ohm and i blew that out within...

Answer:

If the amp claims to be 1100w max then you can bet the rms is about 550-600w. This means that you can...

Ian at Yahoo! Answers Mark as irrelevant Marked as irrelevant Undo

Is 800rms too much for a 600 rms sub? And if so Couldn't I simply keep the Amp's Gain Remote At 3/4 up or so?

Amp - Boss CH-1500 Class D Mono - 540rms @ 4ohm / 800 rms @ 2 ohm - 1500 peak Sub - (Single) Kicker S12L5 - DVC - 1200 peak / 600 rms Enclosure - Slot Port Vented and Tuned to 35hz

Answer:

i would keep the gain at much lower then that, but with Boss amps, I doubt you'll get that much wattage...

deadmanj... at Yahoo! Answers Mark as irrelevant Marked as irrelevant Undo

800 watt rms amp powering a 1000 watt rms 12" sub?

Do you guys think this amp will make my sub really hit hard? I have a hifonics amp and at 4ohms bridged it can put out 800 watts rms. it's cea compliant so i know thats what the power is on the amp, but do you think it's enough for the sub? BTW the subb...

Answer:

Assuming the sub in your link is the exact model that you own, you have a problem: it's not possible...

KaeZoo at Yahoo! Answers Mark as irrelevant Marked as irrelevant Undo

Can I run 2 dvc 4ohm subs at a 1ohm load on a mono amp?Subs are 400w rms each, amp is 1000w rms at 1 ohm?

They are two pioneer subs and a hifonics amp. I haven't got the amp yet but it is the one i want. Should i get a two channel amp instead?

Answer:

yes you should buy a two channel 400 watt per channel so that you don't over load your speakers but...

3D4ZT2YK4XYK47NPUWUWCZ5WUA at Yahoo! Answers Mark as irrelevant Marked as irrelevant Undo

My 12' alpine type r dual 4ohm vc sub is 500 rms,my amp is a mtx thunder150rms@4ohm-300rms@2ohm how can i get

what i want to know is how do i hook up my sub to get the 300 rms from the amp? and can my sub be hooked up to get 2ohm if its dual 4ohm vc? and will it sound ok

Answer:

You can wire a dual 4-ohm voice coil for 2 ohms by wiring the coils in parallel. Here's a diagram: http...

jesse m at Yahoo! Answers Mark as irrelevant Marked as irrelevant Undo

Does somebody know of an amp that is ACTUALLY 1-ohm stable? 800 watts RMS and a good brand?

I have 2 kicker comp vrs, 400 watts each, 1 ohms, 12 inchers in a sealed box. I have had the brutus hifonics amp that's 800 watts rms and SUPPOSED to be 1 ohm stable but it sounded like **** (cuts out, bottoms out, etc..), same with the Kenwood i have...

Answer:

hifonics amps are stable to 1 ohm and are close on their ratings for the non cea2006 comp. amps dont...

T!ka :) at Yahoo! Answers Mark as irrelevant Marked as irrelevant Undo

Related Q & A:

What is the difference between a 2ohm sub and a 4 ohm sub?Best solution by knowledge.sonicelectronix.com
How can I power 4 speakers with a 2-channel amp?Best solution by Yahoo! Answers
How to wire one 4ohm dvc sub to a monoblock amp so that its a 4 ohm load?Best solution by Yahoo! Answers
Can I use a 4 ohm crossover with a high pass slope of 24 db with a 6 ohm tweeter that has a 6 db slope?Best solution by termpro.com
What would be better a 2-ohm sub or a 4-ohm sub?Best solution by ChaCha

Just Added Q & A:

How many active mobile subscribers are there in China?Best solution by Quora
How to find the right vacation?Best solution by bookit.com
How To Make Your Own Primer?Best solution by thekrazycouponlady.com
How do you get the domain & range?Best solution by ChaCha
How do you open pop up blockers?Best solution by Yahoo! Answers

For every problem there is a solution! Proved by Solucija.

Got an issue and looking for advice?
Ask Solucija to search every corner of the Web for help.
Get workable solutions and helpful tips in a moment.

Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.