How to hook up two or three amps?
Let’s learn how to hook up two or three amps. The most accurate or helpful solution is served by Yahoo! Answers.
There are ten answers to this question.
Best solution
I have 2 12" kickers i want one amp per sub to push them and another amp to push all my other car speakers and i want to have a bass controll knob for the subs that controll both as if they were one sub and hook all that up to my head unit, im not sure what crossover kit to get and how to hook up all the remote wires, i have pretty much everything else like the power block distributer and all the other wires, im just a little bit iffy on what exactly to buy
Answer:
I don't know of any "bass control knob" that can cortrol 2 amps at the same time. If your...
Randy at Yahoo! Answers Mark as irrelevant Undo
Other solutions
PJ4JGCWC733DMMOBGK5VK4ZGMM at Yahoo! Answers Mark as irrelevant Undo
i have two 4 ohm single voice coil kenwood subs 400 rms each. a have a 1000 watt kenwood amp 2 channel mono 300 rms x2 2 ohm stable and a nitro bmw 484 1200 watt amp not sure on the rms but i think i might be lower than the kenwood it is a 2 channel...
Answer:
id say run both subs parallel to the kenwood amp only.... bridge it and run them both to it...
D T at Yahoo! Answers Mark as irrelevant Undo
im getting 2 mtx terminators and im getting 2-4 pioneer 5-way speakers. The subs produce 1200watts max/but together about 400 watts rms and the pionners are going to be about 200 watts rms. but anyway what my question is, is it better to get separate...
Answer:
First, the terminators do NOT take that kind of power, you should get an amp thats about 500w rms and...
Jacob Schneider at Yahoo! Answers Mark as irrelevant Undo
I have 2 18" Solo X speakers. And 2 4500rms amps. i was wondering if i could hook both amps up to one sub.
Answer:
If the SoloX is a dual voice coil sub, you should be able to wire an amp to each voice coil.
Mr. Mathew at Yahoo! Answers Mark as irrelevant Undo
Hi I have two 12" type r 2ohm subs the are 500 watts and 1500 watts peak power. I have an alpine mrp-m1000 watt amp powering them. 500 watts to each sub. My question is can I hook two of these amps up one to each sub for a total of 1000 watts each...
Answer:
yes u can it just put alot of strain to ur alt. u need a Y splitter so u can hook both of them up and...
chris at Yahoo! Answers Mark as irrelevant Undo
i have a massive 1500 watt pro S amp and i wanna hook up a 380 watt 4 channel amp for my mids and highs but idk how to hook up two amps . like how do i get power to the second amp. my ...show more
Answer:
Actually to do this the safest way is to get a distribution block. Then cut your current power wire...
MJ2CLJEWLR6Q4JD2ZLLZ6AEZBY at Yahoo! Answers Mark as irrelevant Undo
I have 2 amps for my truck one is for the speakers and one is for the subs. i was wondering how to hook up the remote wire to both of the amps. do i spilt them or what do it do. and ...show more
Answer:
hook them up all the same wire. all a remote wire is , is to turn the power on and off when u turn your...
NYY6W5LFNDXRFMK2XLTYB3IKWI at Yahoo! Answers Mark as irrelevant Undo
I have a 1000(peak) watt amp and a 2800(peak) watt amp i want to connect both. Can I take the wire coming from my battery and use a distribution block to split the 4 guage into two 8 gauge wires, or do I need bigger ones? Also do I need to use two fuses...
Answer:
you need to look at the fuse sizes of both amplifiers and add them together. then use this link to find...
weston at Yahoo! Answers Mark as irrelevant Undo
I have two 1 ohm resistors (rated at 10w of course!) and I want to use a 3V input and get 2.8-3.0V output but I think if i just put them in series and I use R = V/I i get 2ohms=x volts/1.5 amps but then i get three for the volts which wouldn't that be...
Answer:
You need resistors with much less than one ohm. A 10 amp fuse might drop 0.1 volts at 1.5 amps. That...
Yahoo! Answers Mark as irrelevant Undo
Related Q & A:
- How do I compare two tables with the same column definitions in different schemas?Best solution by Database Administrators
- How to switch between two tables?Best solution by Stack Overflow
- How do I bridge two different amps together?Best solution by ecoustics.com
- How do I hook up two motors on my boat?Best solution by Yahoo! Answers
- How can I hook up two monitors to my PC?Best solution by Yahoo! Answers
Just Added Q & A:
- How many active mobile subscribers are there in China?Best solution by Quora
- How to find the right vacation?Best solution by bookit.com
- How To Make Your Own Primer?Best solution by thekrazycouponlady.com
- How do you get the domain & range?Best solution by ChaCha
- How do you open pop up blockers?Best solution by Yahoo! Answers
For every problem there is a solution! Proved by Solucija.
-
Got an issue and looking for advice?
-
Ask Solucija to search every corner of the Web for help.
-
Get workable solutions and helpful tips in a moment.
Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.