What's the best amp for two "dual" Kenwood KFC-W3012?

I have two 12" 4 ohm Punch P3s with a Kenwood KAC-9152D amp RMS Power: 500W x 1 @ 4 ohms while 900 at 2ohms

  • the amp is at a very low setting(basically minumum) but when I cut it up it gets hot and cuts off. I also changed settings(midway to hallf wattage) and it still gets hot and cuts off I don't even use the bass boost. Its set at 50hz not 40hz whats the deal. Is kenwood really garbage? Help me!!!

  • Answer:

    The P3 subs are DVC subs. Do you have the coils of each sub wired in parallel (+ to + and - to -) or in series (+ of one coil going to the - of the other coil and the remaining + and - to go out to the amp or whatever)? If you have the coils of each wired in parallel and then you connected the positive and negative wires of both speakers together, then you will have a 1ohm load for the amp. Of course, this amp has "two channels" which combine the ohm load of each "channel" internally by combining both positives and both negatives together internally. This is inherently wiring whatever it sees on each "channel" in parallel. So, if you have each sub's voice coils wired and parallel and you connect one sub to each of the "channels" on the amp, the amp is reading it all as a 1ohm load. Kenwood claims this amp is stable at 1ohm, 900 watts even. Personally, I doubt this, just given my experience with Kenwood. They are good but I've seen their products not stand up to what they are supposed to be. You need to make sure your amp has adequate air flow so check out where you have it mounted. You dont want have a punch of stuff on the top of it so that air cant get to the chassis of the amp and assist in cooling. It's a class d amp so it should run relatively cool but still, things can happen. If you have a blown coil on one of the subs, that can cause the amp to go into failure. It depends on what specifically is damaged on the voice coil, but I've seen this before: a coil is shorted but the speaker still plays (off of one coil). The amp still puts out wattage but it also sees the short. It can go into thermal shut down, if not failure as a result. You can pull each sub and use a digital multimeter to test the impedence of each coil. You should get something around 4ohms on each... 3.8 to 4.1 or so. If you get something bizarre, then you may have a problem (or a low battery in your DMM). If this is not the case and the amp is mounted in a good place, then you may have an amp that is not able to consistently do what it's supposed to do. You can take back to where you got it and try to exchange it or send it to Kenwood. You're next most efficient ohm load that you can wire up with those two subs is 4ohms. This should play (provided you dont have a bad sub) but it wont be to the maximum ability claimed by the amp. Just for kicks, if your subs turned out okay when you tested the impedence, try wiring one sub in parallel and to the amp, just one. This will give a 2ohm load to the amp. see what it does with that. Good luck!

life's good at Yahoo! Answers Visit the source

Was this solution helpful to you?

Other answers

I would suggest a JL audio amp. works great for my type R's

Mike C

The issue may be in how the sub is wired and the configuration of the subs themselves. We need to know if the subs are dual voice coils or single and the ohms they are. Y!IM me an I'll help you get this up and running. [email protected]

sparky3489

check your conections bridgeing and wireing in series will drop you ohms rating and over heat the amp.check out the guide for stereos at checker its with the chiltons

iamwhoiam151

Find solution

For every problem there is a solution! Proved by Solucija.

  • Got an issue and looking for advice?

  • Ask Solucija to search every corner of the Web for help.

  • Get workable solutions and helpful tips in a moment.

Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.