Need help double checking my answers(ELECTRIC HEATING APPLIANCES AND FANS)?
-
1. In selecting the wire size for a line cord, you should remember that A. No. 16 is larger than No. 12. B. No. 14 carries more current than No. 18. C. No. 8 is smaller than No. 10. D. No. 4 carries less current than No. 6. 2. Which one of the following appliance parts gets the hardest service? A. Switch B. Thermostat C. Heating element D. Line cord 3. The color used for the hot side of house wiring is A. green. B. white. C. gray. D. black. 4. An AWG No. 16 line cord with type HPN insulation has an ampacity of A. 12 amp. B. 13 amp. C. 15 amp. D. 17 amp. 5. To heat a room quickly, some electric room heaters are provided with A. a heavy metal case. B. a motor-driven fan. C. a push-button switch. D. an automatic thermostat. 6. If the current flowing through an electric heater increases from 6 to 12 amp while the voltage remains the same, the heat produced by the heater will be A. reduced one-half. B. unchanged. C. two times the original heat. D. four times the original heat. 7. The wires used in a heating element are usually made of A. copper. B. steel. C. aluminum. D. Nichrome. 8. Why does a thermostat blade bend when heated or cooled? A. It is made of two different materials. B. There is a difference in temperature between the blade ends. C. Different currents are applied to each end. D. Mechanical pressure is caused by the high resistance. 9. When you are checking an electric heating appliance, the first test made should be for A. excessive leakage. B. the normal voltage supply. C. an open circuit. D. low resistance. 10. Why should you NOT repair heating elements by soldering? A. Solder does not conduct electric current. B. Solder joints are mechanically too weak. C. Solder melts at the operating temperature of the heater. D. Soldered joints have too high a resistance. 11. What type of selector switch can be used to control the heat output of three elements connected in parallel? A. SPST switch B. DPST switch C. DPDT switch D. Shorting-bar-type switch 12. Thermostats used in electric irons differ from those in small room heaters in that they are A. smaller in size. B. operative at higher temperatures. C. connected directly to the appliance plug. D. mechanically more fragile. 13. How can you clean out the scales in an electric iron without taking the iron apart? A. By blowing out the holes with compressed air B. By scraping the tank and tubes with a drill bit C. By brushing the clogged tubes with a stiff wire brush D. By rinsing the tank and holes with a water-diluted chemical 14. Bus bars are used in an electric iron as A. thermostat supports. B. heat-adjusting resistors. C. connectors between the thermostat and the element. D. electrical terminals. 15. The water in a spray iron is prevented from returning to the tank by the action of a A. suction tube. B. check valve. C. water pump. D. pressure spring. 16. The heating element in an electric iron is in good working order if the resistance across the terminals of the element reads approximately A. 0 ohms. B. 15 ohms. C. 120 ohms. D. 1000 ohms. 17. Why does the heat of the heating element stop when the desired temperature in an electric iron is reached? A. The thermostat blade opens electrical contacts. B. The circuit through the element is closed. C. The switch bypasses the thermostat. D. The contacts on the blade touch. 18. Jumpering out the resistors in a resistance-controlled three-speed fan will cause the motor to A. run at highest speed. B. run at medium speed. C. run at lowest speed. D. stop immediately. 19. A fan equipped with a gearbox is capable of A. running at three speeds. B. being tilted downward. C. oscillating from side to side. D. reversing the direction of the motor. 20. If the fan blades rattle while the fan is turning, you can stop the noise by A. oiling the blades. B. adjusting the blade angles and the blade tip position. C. tightening the motor end bells and motor mounts. D. cleaning the blade surfaces. 21. The recommended way to hold a loose hub on a fan is by A. riveting. B. soldering. C. welding. D. cementing. 22. Quiet operation of a fan depends mostly upon the A. weight of the blades. B. material of the blades. C. motor balance. D. balance of the blades. 23. The blades of small fans are made of A. aluminum. B. steel. C. tin. D. copper. 24. A modern varia
-
Answer:
This is rediculous
Bob D at Yahoo! Answers Visit the source
Related Q & A:
- I need help on what I need to buy or do.Best solution by Yahoo! Answers
- I need help with some horse questions, can you help me.Best solution by Yahoo! Answers
- I need help with Adobe Photoshop.Best solution by Yahoo! Answers
- I did something really bad and now i need help please help me.Best solution by Yahoo! Answers
- What sort of opportunities are there to help people in Africa or places where people need help?Best solution by Yahoo! Answers
Just Added Q & A:
- How many active mobile subscribers are there in China?Best solution by Quora
- How to find the right vacation?Best solution by bookit.com
- How To Make Your Own Primer?Best solution by thekrazycouponlady.com
- How do you get the domain & range?Best solution by ChaCha
- How do you open pop up blockers?Best solution by Yahoo! Answers
For every problem there is a solution! Proved by Solucija.
-
Got an issue and looking for advice?
-
Ask Solucija to search every corner of the Web for help.
-
Get workable solutions and helpful tips in a moment.
Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.