How do you replace the lighter in a 1999 Mercury Cougar?

How do you replace the alternator on a 1999 Mercury Cougar?

• Answer:

  New With USEFUL Content from Wikibooks From Wikibooks, the open-content textbooks collection < Automobile repair (Redirected from Automobile repair 99 mercury cougar alternator replacement) Jump to: navigation, search Alternator replacement: The placement of the alternator in the 1999 Mercury Cougar can really take the fun out of performing your own automotive repair, but hopefully with these tips you can avoid the 4-hour job taking days instead. 1. Disconnect the negative battery cable. 2. Using a 3/8" drive, release tension on the tensioner and slip the belt off of an accessory. 3. Loosen the passenger side front wheel lug nuts, then raise front of vehicle and remove wheel. 4. Reinstall two adjacent lug nuts onto the brake rotor and using a prybar on the lugnuts and a socket with a breaker bar, loosen and remove the nut from the splined half shaft(this nut supposedly looses its torque ability and needs to be replaced after being loosened). 5. Remove the Stabilizer bar link. This will require two wrenches, one placed near the rubber seal area. (This step caused me a 3-day delay as I had to order a new one when the nut broke off with the bolt intake) 6. Remove the steering knuckle pinch bolt and separate the ball joint from the "A"-shaped suspension component with the appropriate tool or prybar. 7. Remove the "Y"-shaped exhaust pipe from underneath the vehicle. Spraying a lubricant on the 6 studs and nuts will aid the removal of these nuts. (Stripping of these threads is easily done with the galling that can happen from the hot conditions it has undergone. This accounts to adding another 3 days to my repair.If possible tighten the nut 1/8 of a turn before removing to keep from pulling rust into threads) 8. Remove the half shaft after extracting it from the steering nuckle. (It may be just as easy to remove the nuckle prior to removal of the half shaft, even though this requires removing the ABS sensor, brake caliper, and rotor.) A slide hammer can assist on freeing the half shaft from the other half shaft. 9. Loosen the 5 nuts needed to remove the half shaft that goes into the transmission. Apparently this half shaft is balanced from the factory and should be reinstalled in the same allignment, so mark the transaxle and the half shaft to make this possible. Remove the half shaft. 10. There are 3 electrical connections to the alternator: a 3-pin connector that can be removed by slipping off the clip, a 1-pin connector that is removed by gently prying the plastic clip portion up, and a battery cable sized cable that attaches with a nut that can be removed with a 3/16" socket. 11. There are now 4 bolts that need to be loosened before the alternator can be removed. Three of the bolts are easily reached, while the 4th is not visible and will have to be felt for. A 13mm socket will be needed to remove these bolts. The exhaust manifold and the attached O2 sensor blocks access to the hidden bolt, and removal of the manifold has its own set of hidden bolts which makes removal of the manifold to access the alternator bolt unfeasible. 12. Installation is the reverse of the above, but it is highly recommended that you replace the O2 sensor that is now exposed. It uses a square connector, not a round one like the more accessible "catalyst monitor" sensors. This vehicle has a whopping 4 sensors distributed over 2 banks. If you choose to replace this sensor, a tip on removing the electrical connector: find a 3-inch or so 3/16" diameter or less piece of metal(I used a tap) and using one hand to feel for the access hole which will point to the rear of the vehicle, use the other hand with the metal piece to insert into the hole and releasing the clip, pull on the connector to disconect the heated oxygen sensor. Alternative method This task can also be accomplished WITHOUT removing the drive shafts. Jack the car up as high as possible and support with jack stands. 1. Disconnect the battery. 2. Remove the passenger side wheel & inner fender well covers 3. Remove the exhaust Y-pipe. Soak the seven nuts with penetrating lubricant. 4. Remove the serpentine belt from the alternator. 5. Unbolt the upper roll bar mounting point from the strut. 6. Unbolt the steering joint & press out of the steering arm. At this point you should be able to see the bottom portion of the alternator. 7. From under the car you should see a bracket that supports the intemediate shaft. Unbolt the two nuts that connect the intermediate shaft bearing to the bracket. 8. Unbolt the three bolts that hold the bracket to the engine. Then remove the bracket. You now have enough room to get to the alternator bolts. 9. Use a 13mm socket with a universal joint on the end of a long extension to get to the upper alternator bolt. I was able to reach around into the wheel well with my right hand up to the top of the alternator bolt to help guide the socket onto the bolt. 10. The bottom bolt is easy to get to. But the universal makes it a little easier, because the Intermediate shaft is still there. 11. The rear alternator bracket is removed with a 10mm socket. 12. Once the bolts are out you make need to pry the alternator out of the bottom of its mount. 13. Once loose, pivot the alternator on its pulley down towards the control arm. If you are having problems bringing the alterantor down past the rubber boot, just rotate the brake disk and it will walk the alternator out. You will have easy access to the electrical connections. Replace with new alternator and reverse the process. While you are down there you can splice a jumper wire from the Red wire in the three wire plug over to the "Output" terminal of the alternator. Question: Why? : It gives the voltage regulator a better reading than the factory wire that runs all over the engine compartment. The factory did the same thing in the later model cars. I think there was even a recall for this. If your battery light flickers when the engine is rev'd up than this is an inexpensive mod that may fix your problems. Retrieved from "http://en.wikibooks.org/wiki/Automobile_repair/99_mercury_cougar_alternator_replacement" Original When you are wanting to take out the alternator you have to take off the plastic wheel well from the inside.First things first you have to have a 13mm socket and about 3 or four long extensions also you must have a swivle extension.It will be a tight sqweeze but you can do it believe me,go for the top bolt first because its the hard one.You will have to make sure your extensions are long enough to get leverage on it then just crank it.Next is the bottom bolt fairly easy to do it comes out the same way. Just to save everyone alot of hassle when it comes to this job, you can get easy access to it just by pulling the plastic inserts from the right side wheel well, now this is for the 2.5L v6 just FYI. and using a few extensions and an flex swivel ratchet head, theres a 10 mm bolt and also 2 1/2 inch which are for the alternators ears they go directly diagonal to each other now you will need to pull your tie rod from the wheel assembly to get the alternator out it will not fit through the space provided but it saves time, parts and is a lot less aggrevating then the above methods. took me 4 hours today to complete.