Find solution
How do you program the remote keyless entry for a 2000 Pontiac Sunfire?

How do you program a remote keyless entry for a 2000 pontiac grand prix?

  • Answer:

    Actually, this procedure is for a Grand Prix. But, it should work on a Grand AM, also. Good luck! Best Answer - Chosen by Voters How do i programm my keyless remote for monte carlo 2001? Best Answer - Chosen By Voters Thro, this procedure is actually for the Grand Prix. I would think it is the same for the Monte Carlo. Good luck! GRAND PRIX KEY FOB PROGRAMMING INSTRUCTIONS Transmitter Programming No Tools Required In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed. Important Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters. Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver. Perform the following steps: Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat) Remove the ignition key from the ignition lock cylinder. Close all of the vehicle's doors. Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis. Turn the ignition lock cylinder to the ACC position. Turn the ignition lock cylinder OFF, then back to ACC within 1 second. Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1. Important After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds. Repeat step 8 in order to program each additional transmitter. Remove the ignition key from the ignition lock cylinder. Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis. Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation .

S3I4NN22Y3QPN2VCMJHLN2XM24 at Yahoo! Answers Visit the source

Was this solution helpful to you?

Other answers

Transmitter Synchronization IMPORTANT: Loss of transmitter synchronization will occur when the following conditions are present: If the transmitter is activated more than 256 times while the transmitter is out of range of the remote control door lock receiver. After the transmitter battery replacement, if the transmitter is immediately activated more than 16 times while the transmitter is out of range of the remote control door lock receiver. In order to resynchronize the transmitter, press and hold the transmitter LOCK and UNLOCK buttons simultaneously for at least 7 seconds , or until the following condition is present, the horn sounds 3 times. Perform the transmitter resynchronization procedure if the following conditions exist: The batteries on the keyless entry transmitter have been replaced. A keyless entry transmitter is malfunctioning. Transmitter Programming Perform the following procedure when replacing transmitter(s). IMPORTANT: Once entering this procedure, programming the first transmitter erases all previous transmitters. You must program all transmitters. Program one vehicle at a time. One transmitter could be programmed into other vehicles that are also on program mode in close proximity. 1. Pull the MALL PGM Fuse. 2. Turn the ignition switch to the ACC position. The seat belt indicator flashes and the chime sounds 2, 3 or 4 time . This action identifies which type of BCM, is installed on the vehicle. Check that the BCM installed on the vehicle is compatible with all of the features on the vehicle. Keyless entry requires BCM type 3 or 4. 3. Turn the ignition switch from the ACC position to the OFF position, then back to the ACC position within 1 second. This action causes the BCM to enter the diagnostic/program mode. The BCM may flash and chime Diagnostic Trouble Codes (DTCs) . The number of flashes and chimes equals the DTC number. If there are DTCs in memory, record the DTCs and perform the appropriate repairs. 4. Open and close any vehicle door. You should hear a chime if you are in the diagnostic/program mode. If unable to enter diagnostics, there is a control module problem. 5. Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for 14 seconds. At the 7-second mark, you may hear a chime. This chime feedback indicates that the transmitter has been resynchronized. Continue holding the lock arid unlock buttons until hearing another chime ground the 14-second mark. This chime feedback indicates that the transmitter has been programmed successfully. 6. Repeat step 5 for the rest of the transmitters (for a total of 4 transmitter). 7. Exit the BCM diagnostics/programming mode: Turning the ignition switch to the LOCK position. Reinstall the MALL PGM Fuse.

Uncle Red

Related Q & A:

Just Added Q & A:

Find solution

For every problem there is a solution! Proved by Solucija.

  • Got an issue and looking for advice?

  • Ask Solucija to search every corner of the Web for help.

  • Get workable solutions and helpful tips in a moment.

Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.