How to get three different routers into one cohesive network?
-
I have three different wireless routers on my home network, and they are not inter-operating well... So I have three different wired/wireless routers in my home network and they're causing me some headaches. An older http://www.actiontec.com/189.html router that acts as a gateway between the internet and my home network. Since it's only capable of 80211.g, the wireless is disabled and it's only purpose in life is to provide data to the second router.A http://www.wdc.com/en/products/products.aspx?id=710. It has a few devices connected via Ethernet, but it also provides my wireless network. This is my main router in my living room, and runs in the 192.168.6.* subnet. A http://www.tenda.cn/tendacn/product/show.aspx?productid=352 that is configured to operate as a wireless network bridge (WDS mode), and it has a few devices connected to it via ethernet. It's in my office, all the way on the other side of my house, and any wired device connected to it is in the 192.168.10.* subnet.The end result is that anything that is connected via ethernet to the Tenda device in my office cannot see the rest of the wireless. From the reading I've been doing, it seems like this is because they're on different subnets. So it means I'm having some annoying issues, like my Roku device connected to the wireless network in my living room can't see the Plex server that's on a machine in my office. Or my wife's laptop being unable to see my office computer in Windows. What is the best way to set up a home network with the above configuration so that ALL devices can see each other? Is there any way I can configure the routers to be visible each other across subnets? Should I get rid of the Tenda (which is not the greatest router, but it was cheap)?
-
Answer:
What network mask are you using on the Tenda and the WD? If it's 255.255.255.0, change it on both to 255.255.0.0 and everything should be able to see everything.
Fidel Cashflow at Ask.Metafilter.Com Visit the source
Other answers
Have you tried disabling DHCP on the Tenda? Having it enabled might be what's causing the WLAN and LAN to be partitioned into separate (and in the case of the local ethernet, NATed) networks.
RonButNotStupid
Yeah, this gets complicated. Most routers have an option to operate in "AP mode" where they act strictly as wireless APs and let another router on the network handle DHCP assignments - this is probably where you want to start. You want a single device handing out IP addresses across all 3 APs.
kbanas
Have you tried disabling DHCP on the Tenda? Having it enabled might be what's causing the WLAN and LAN to be partitioned into separate (and in the case of the local ethernet, NATed) networks. I thought the same thing, so I disabled DCHP on the Tenda. It didn't help, unfortunately. The handful of devices I have plugged in via ethernet are all configured using static IPs in the 192.168.10.* subnet. What network mask are you using on the Tenda and the WD? If it's 255.255.255.0, change it on both to 255.255.0.0 and everything should be able to see everything. Neither the WD nor the Tenda's Web UI's will accept a 255.255.0.0 subnet mask. Yeah, this gets complicated. Most routers have an option to operate in "AP mode" where they act strictly as wireless APs and let another router on the network handle DHCP assignments - this is probably where you want to start. You want a single device handing out IP addresses across all 3 APs. I thought setting the Tenda in WDS mode would accomplish that, but it apparently does not. The Tenda get's an WLAN IP in 192.168.6.* subnet, but all ethernet devices are restricted to the 192.168.10.* subnet. I'm beginning to think the Tenda is just a piece of crap. I tried to do some port forwarding to poke holes in for a few services via the WebUI, but I still couldn't get anything to see each other. I actually did a port scan using zenMap, and it reported that all ports on the tenda were closed! Anyone have a suggestion for a decent wireless N router that can operate in AP mode and provide at least a consistent 50Mbps of throughput? Even better if I could put DD-WRT on it...
Fidel Cashflow
what is the subnet between the Verizon and the two routers? A Tenda W368R that is configured to operate as a wireless network bridge (WDS mode), So my understanding is that means this device is configured to just pass traffic through to (I assume) the Verizon device? If so you've got statically assigned 192.168.10.x devices attempting to talk to the LAN side of the Verizon device, which I'm guessing is assigned to some other subnet. Post some ipconfigs from the working and not-working clients.
banshee
what is the subnet between the Verizon and the two routers? The Verizon router is running at 192.168.5.1. The wireless is turned off, and only the WD router is connected to it via ethernet. So my understanding is that means this device is configured to just pass traffic through to (I assume) the Verizon device? It should be configured for WDS, which I think essentially 'forwards' the packets to the WD router. Post some ipconfigs from the working and not-working clients. This is from the non-working computer in my office that's behind the Tenda. Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Qualcomm Atheros AR8151 PCI-E Gigabit Ethernet Controller (NDIS 6.30) Physical Address. . . . . . . . . : 90-2B-34-3D-EE-B4 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::709b:72c1:52fe:c012%2(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.10.100(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.10.1 DHCPv6 IAID . . . . . . . . . . . : 361769780 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-CB-3B-8E-90-2B-34-3D-EE-B4 DNS Servers . . . . . . . . . . . : 192.168.6.1, 8.8.8.8 NetBIOS over Tcpip. . . . . . . . : Enabled
Fidel Cashflow
Related Q & A:
- How To Connect Two Different Network Segments Using A Switch And A Router?Best solution by Super User
- How to get the name of the currently connected WiFi network?Best solution by Stack Overflow
- How to get different fonts on Facebook?Best solution by symbols-n-emoticons.com
- How to get a job when no one is hiring you?Best solution by ChaCha
- How can I look at insurance quotes for different cars at one time?Best solution by allstate.com
Just Added Q & A:
- How many active mobile subscribers are there in China?Best solution by Quora
- How to find the right vacation?Best solution by bookit.com
- How To Make Your Own Primer?Best solution by thekrazycouponlady.com
- How do you get the domain & range?Best solution by ChaCha
- How do you open pop up blockers?Best solution by Yahoo! Answers
For every problem there is a solution! Proved by Solucija.
-
Got an issue and looking for advice?
-
Ask Solucija to search every corner of the Web for help.
-
Get workable solutions and helpful tips in a moment.
Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.