How to wire 2 dvc subs to mono amp?

1 got 3 different amp's to choose from which is best for my 2 dvc 4ohm subs,and how do i wire it 4 more boom?

• i have two 4ohm dvc PERFORMANCE TEKNIQUE sub 500 rms,and three amps to choose from but dont know wich is the best for my subs could you let me know which of them you think ill get more power from and how to wire that subs to that amp? here are the specs..---------------PERFORMANCE TEKNIQUE SUBWOOFER CBM-5712 • Size: 12” • Max Power: 1000W • Dual Voice Coil Aluminum Cone • Aluminum Die-cast Basket • Hard Aluminum Cone • Dual 4Ω+4Ω Voice Coil • 2/4/8Ω Operation • Bumped and Vented T-Yoke • High Temperature 4-Layer Voice Coil • Voice Coil Cooling Ventilation System • Double Damper • Heavy Duty Industrial Magnet Structure • Push Button Terminals • Rubber Edge Surround Rubber Covered Lead Wires ICBM 5712DX Specifications: Magnet: 160 oz. Double stacked Ferrite magnets Frame: 5 spoke Die-cast aluminum basket Cone: Reinforced aluminum curvilinear Surround: Oversized buytl rubber Spider: 2 Flat ultra excursion Power handling: 500 watts RMS, 1,000 Watts Program (conservative) T Yoke: Industrial Chromed Hex bolt retained, Bumped and Vented Double damper magnetic motor assembly Cooling: Double Vented (T Yoke and Motor Side vents) Voice Coils: 4 Layer Dual 4 Ohm High Temperature black Aluminum Voice Coil Diameter: 2.2" Nominal impedance: 4 ohms / per coil DC resistance (Re): 3.2 ohms each coil Frequency range: 20 Hz-1.1 kHz Fs:30 Hz QTS:.526 QES:.614 QMS:7.698 VAS:56L SD:.0491M SPL:90 dB 1W/1m Xmax:16mm Mounting Depth: 165 MM Mounting Hole Dia.:296 MM Net weight: 22lbs Suggested Retail Value is: $169.95 ----------------------------------------… TEKNIQUE 8OOW ICBM-772 2 Channel Bridgeable Power Amplifier • 24dB/OCT. Crossover Slope • Variable Subsonic Filter (10Hz-100Hz) • Variable Low Pass Filter (30Hz-500Hz) • Variable High Pass Filter (50Hz-1KHz) • Variable 18dB Bass Boost • High and Low Level Input Through RCA • Double Sided PCB • Dual Protection (Thermal & Short Circuit) • RCA Line Out (Preamp) • Power & Diagnostic LED Indicator • 2 Ohm Stable Stereo • Soft Delayed Power On • Tri-Mode Capability 0.05% THD Specifications Key Features Amplifier TypeDual Channel Bass BoostWith Bass Boost BridgableBridgable Power Output RMS Power at 4 Ohms125 W x 2 RMS Power at 2 Ohms175 W x 2 Performance THD at Rated RMS Power0.05 % Signal to Noise Ratio95 dB Frequency Response15 Hz - 40000 Hz High - Pass Frequency50 Hz - 1000 Hz Low - Pass Frequency30 Hz - 500 Hz Dimensions Depth15.90 in. Height2.12 in. Width9.96 in. Other Features 3 Way ReadyYes Input Voltage0.2 volt *AMERICA PRO BASS MACHINE VS-8877 1600w 4CH AMPLIFIER* 400W x 4CH (1600W) @ 2OHM MAXIMUM 165W x 4CH (@ 2OHM) LESS THAN 0.5% THD 110W x 4CH (@4OHM) LESS THAN 0.3% THD MONO: 330W x 2CH (@4 OHM) LESS THAN 0.5% THD ALL MEASUREMENTS DONE AT 14.4VDC, 1KHz INPUT SIGNAL FREQUENCY RESPONSE: 20Hz-20KHz 2 OHM LOAD CAPABLE IN STEREO MODE ONLY LOW PASS FILTER VARIABLE 30Hz-250Hz HIGH PASS FILTER VARIABLE 50Hz-1KHz HIGH AND LOW ADJUSTABLE LEVEL INPUT MOSFET DC-DC SWITCHING POWER SUPPLY LED INDICATED POWER STATUS BUILT IN PROTECTION AGAINST SHORT CIRCUIT AND HIGH TEMP BASS BOOST (+5dB @100Hz) AUTO POWER ON/OFF BY REMOTE +12V DIMENSIONS: (mm) 300(W)x53(H)x613(L) 2 YEAR WARRANTY ----------------------------------------… GM-5200T Features: o Bridgeable 2-Channel Power Amplifier o Peak Music Power : 760W o Continuous Power :  125W x 2 @ 4 ohm  190W x 2 @ 2 ohm  380W x 1 @ 4 ohm bridged o Frequency Response : 10Hz - 50kHz o Impedance : 4 Ohm o S/N Ratio: 75 dBA (Reference: 1W into 4 Ohm) o Dimensions: 11-13/16" x 2-3/8" x 13-1/4" o PWM Regulated MOSFET Power Supply o Balanced Isolator Input Circuit o Oversized Screw-Type Power/Ground Terminals o 2 Channel RCA Inputs o Speaker Level Input o Screw-Type Speaker Terminals o Hi-Volt Input Level Control (400mV-6.5V) o Bass Boost (50Hz, 0/6/12dB) o LPF Crossover Type o Crossover Frequency : 80Hz o Crossover Slope : -12dB/oct

• Answer:

  All three of those amps are NOT enuff to power TWO of your subs. you have two subs that are 500rms EACH with 1000watt PEAK... Based off 500 each=needing 1000watts RMS to both....AT minimum to hit RMS. So assuming you want to get full potential, none of the amps listed will do that. The first amp: Power Output RMS Power at 4 Ohms125 W x 2 RMS Power at 2 Ohms175 W x 2 so 175*2=350 2nd amp: 400W x 4CH (1600W) @ 2OHM MAXIMUM 165W x 4CH (@ 2OHM) LESS THAN 0.5% THD 110W x 4CH (@4OHM) LESS THAN 0.3% THD this is a 4 channel amp. And might (I SAY MIGHTTTTT) be able to give you the MOST power out of all of the others....but you are looking at 400w a channel. so using two channels of the 4 would grant you 800 watts.... And the last amp: Continuous Power : 125W x 2 @ 4 ohm 190W x 2 @ 2 ohm 380W x 1 @ 4 ohm bridged 380 watt...RMS....at 4 ohm Bridged.... Not enuff for two 500watt rms (1000watts total) subs. And realize these subs can/will peak at 1000 per sub as well...so in essence take up to 2000 watts at times...(burps...) but not all the time... I would look at getting a mono amp that will handle 1000watt RMS. That is my suggestion.